View MC100H607_82988.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Registered Hex PECL/TTL Translator MC10H607 MC100H607
The MC10H/100H607 is a 6-bit, registered PECL to TTL translator. The device features differential PECL inputs for both data and clock. The TTL outputs feature 48mA sink, 24mA source drive capability for driving high fanout loads or transmission lines. The asynchronous master reset control is an ECL level input. With its differential PECL inputs and TTL outputs the H607 device is ideally suited for the receive function of a HPPI bus type board-to-board interface application. The on chip registers simplify the task of synchronizing the data between the two boards. The device is available in either ECL standard: the 10H device is compatible with MECL 10HTM logic levels, with a VCC of +5.0 volts, while the 100H device is compatible with 100K logic levels, with a VCC of +5.0 volts.
FN SUFFIX PLASTIC PACKAGE CASE 776-02
* * * *
Differential ECL Data and Clock Inputs 48mA Sink, 15mA Source TTL Outputs Single Power Supply Multiple Power and Ground Pins to Minimize Noise
Pinout: 28-Lead PLCC (Top View)
Q3 25 Q2 Q1 Q0 TGND CLK CLK VBB 26 27 28 1 2 3 4 5 D0 6 D0 7 EGND 8 D1 9 D1 10 D2 11 D2 VCCT 24 Q4 23 TGND 22 Q5 21 VCCT 20 MR 19 18 17 16 15 14 13 12 D5 D5 D4 D4 VCCE D3 D3
MECL 10H is a trademark of Motorola, Inc.
9/96
(c) Motorola, Inc. 1996
2-316
REV 2
MC10H607 MC100H607
LOGIC DIAGRAM 1 OF 6 BITS Dn Dn
D
Q
Qn
CLK R
CLK CLK MR VBB
PIN NAMES
Pin D0 - D5 D0 - D 5 CLK, CLK MR Q 0 - Q5 VCCE VCCT TGND EGND Function True PECL Data Inputs Inverted PECL Data Inputs Differential PECL Clock Input PECL Master Reset Input TTL Outputs PECL VCC TTL VCC TTL Ground PECL Ground
TRUTH TABLE
Dn L H X MR L L H TCLK/CLK Z Z X Qn + 1 L H L
Z = LOW to HIGH Transition
DC CHARACTERISTICS (VCCT = VCCE = 5.0V 5%)
Symbol IEE Characteristic ECL Power Supply Current 10H 100H TTL Supply Current TTL Supply Current Min TA = 0C Typ Max 70 65 100 100 85 80 120 120 Min TA = + 25C Typ Max 70 70 100 100 85 85 120 120 Min TA = + 85C Typ Max 70 75 100 100 85 95 120 120 mA mA Unit mA Condition
ICCL ICCH
MECL Data DL122 -- Rev 6
2-317
MOTOROLA
MC10H607 MC100H607
10H PECL DC CHARACTERISTICS (VCCT = VCCE = 5.0V 5%)
TA = 0C Symbol IINH IINL VIH VIL Characteristic Input HIGH Current Input LOW Current Input HIGH Voltage Input LOW Voltage 3830 3050 Min Max 255 0.5 4160 3520 3870 3050 TA = 25C Min Max 145 0.5 4190 3520 3930 3050 TA = 85C Min Max 145 0.5 4280 3555 Unit A A mV mV mV VCCT = 5.0V VCCT = 5.0V VCCT = 5.0V Condition
VBB Output Bias Voltage 3600 3710 3630 3730 3670 3790 NOTE: PECL VIL, VIH, VOL, VOH, VBB are given for VCCT = VCCE = 5.0V and will vary 1:1 with power supply.
100H PECL DC CHARACTERISTICS (VCCT = VCCE = 5.0V 5%)
TA = 0C Symbol IIH IIL VIH VIL Characteristic Input HIGH Current Input LOW Current Input HIGH Voltage Input LOW Voltage 3835 3190 Min Max 255 0.5 4120 3525 3835 3190 TA = 25C Min Max 145 0.5 4120 3525 3835 3190 TA = 85C Min Max 145 0.5 4120 3525 Unit A A mV mV mV VCCT = 5.0V VCCT = 5.0V VCCT = 5.0V Condition
VBB Output Bias Voltage 3600 3720 3600 3720 3600 3720 NOTE: PECL VIL, VIH, VOL, VOH, VBB are given for VCCT = VCCE = 5.0V and will vary 1:1 with power supply.
10H/100H TTL DC CHARACTERISTICS (VCCT = VCCE = 5.0V 5%)
TA = 0C Symbol VOH Characteristic Output HIGH Voltage Min 2.5 2.0 Max TA = 25C Min 2.5 2.0 Max TA = 85C Min 2.5 2.0 Max Unit V Condition IOH = -15mA IOH = -24mA
VOL Output LOW Voltage 0.55 0.55 0.55 V IOL = 48mA NOTE: DC levels such as VOH, VOL, etc., are standard for PECL and FAST devices, with the exceptions of: IOL = 48mA at 0.5VOL; and IOH = 24mA at 2.0VOH.
AC CHARACTERISTICS (VCCT = VCCE = 5.0V 5%)
Symbol tPLH++ tPHH+- tPHL+- tPW tr tf tS tH Characteristic Propagation Delay to Output Propagation Delay to Output Minimum Pulse Width Rise Time Fall Time Setup Time Hold Time CLK to Q MR to Q CLK, MR TA = 0C Min Max 5.5 4.6 4.4 1.0 0.5 0.5 1.5 1.5 200 2.0 2.0 7.7. 7.7 7.5 TA = + 25C Min Max 6.0 4.9 4.7 1.0 0.5 0.5 1.5 1.5 200 2.0 2.0 8.2 8.3 8.1 TA = + 85C Min Max 6.7 5.9 5.8 1.0 0.5 0.5 1.5 1.5 200 2.0 2.0 10.0 10.0 10.5 Unit ns ns ns ns ns ns ns mV 0.8 - 2.0V 0.8 - 2.0V Condition CL = 50pF CL = 50pF
VPP Minimum Input Swing 1. Numbers are for both ++ and - - delay MR to Q.
MOTOROLA
2-318
MECL Data DL122 -- Rev 6
MC10H607 MC100H607
OUTLINE DIMENSIONS
FN SUFFIX PLASTIC PLCC PACKAGE CASE 776-02 ISSUE D
B -N- Y BRK U D Z -L- -M- 0.007 (0.180)
M
0.007 (0.180)
M
T L-M
S
N
S S
T L-M
N
S
W
28 1
D
X VIEW D-D
G1
0.010 (0.250)
S
T L-M
S
N
S
V
A Z R C
0.007 (0.180) 0.007 (0.180)
M
T L-M T L-M
S
N N
S
H
0.007 (0.180)
M
T L-M
S
N
S
M
S
S
E 0.004 (0.100) G G1 0.010 (0.250)
S
K1
J
-T- VIEW S
SEATING PLANE
K F VIEW S 0.007 (0.180)
M
T L-M
S
N
S
T L-M
S
N
S
NOTES: 1. DATUMS -L-, -M-, AND -N- DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 2. DIMENSION G1, TRUE POSITION TO BE MEASURED AT DATUM -T-, SEATING PLANE. 3. DIMENSIONS R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5. CONTROLLING DIMENSION: INCH. 6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635).
DIM A B C E F G H J K R U V W X Y Z G1 K1
INCHES MIN MAX 0.485 0.495 0.485 0.495 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 --- 0.025 --- 0.450 0.456 0.450 0.456 0.042 0.048 0.042 0.048 0.042 0.056 --- 0.020 2_ 10_ 0.410 0.430 0.040 ---
MILLIMETERS MIN MAX 12.32 12.57 12.32 12.57 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 --- 0.64 --- 11.43 11.58 11.43 11.58 1.07 1.21 1.07 1.21 1.07 1.42 --- 0.50 2_ 10_ 10.42 10.92 1.02 ---
MECL Data DL122 -- Rev 6
2-319
MOTOROLA
MC10H607 MC100H607
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 or 602-303-5454 MFAX: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 INTERNET: http://Design-NET.com
JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-81-3521-8315 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298
MOTOROLA 2-320
*MC10H607/D*
MC10H607/D MECL Data DL122 -- Rev 6

▲Up To Search▲

Price & Availability of MC100H607

	To Download MC100H607 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .